James Smith        July 22, 2020

How often the ignition coil should be replaced ? The ignition coil is a device that provides energy to the ignition system. As we know, the moving car is powered by the engine , and the engine produces energy by burning the mixture air-fuel in the cylinder, the ignition coil just like a transformer turns a low voltage into a high voltage in this process and the spark plug fire the mixture air-fuel. Generally speaking, the service life of the ignition coil is more than 100,000 kilometers.If your ignition coil does, please replace your ignition coil timely.

James Smith        July 18, 2020

The difference between the independent ignition system and other ignition systems: 1. Different installation methods: the coil of the independent ignition system can be installed directly on the spark plug; other ignition systems cannot be installed directly on the spark plug.

James Smith        July 18, 2020

Double spark plug ignition system is in the hemispherical combustion chamber on both sides of the symmetrical arrangement of two spark plugs of the same type, the two spark plugs and the combustion chamber centre distance is equal, the engine idle or low-speed operation is still using a single spark plug ignition.

James Smith        July 18, 2020

This design is used by some vehicle manufacturers. It combines several single-spark and dual-spark ignition coils into one unit, also known as a rail. It is mounted on several spark plugs simultaneously. One benefit: such systems can be equipped with a flow gauge, which can be used to monitor the combustion quality in the engine control unit.

James Smith        July 17, 2020

Designed to limit energy loss between the coil and the spark plugs, these operate without high tension leads and mounted directly on the spark plugs, taking advantage of restricted space and independent high-voltage source for each cylinder. In modern car, single spark technology is more popular for automotive manufacturers.

James Smith        July 17, 2020

The main reason why the throttle valve is dirty is that the shaft of the throttle valve plate and the joint of the throttle body have carbon deposition, leading to the throttle opening is not accurate enough, thus causing car wobbling at idle. It indicates the throttle body need to be cleaned. If it still shakes after cleaning, the throttle body assembly may be damaged and needs to be replaced.

James Smith        July 17, 2020

Automobile engine wobble, poor acceleration and fault lights, generally it was assumed that the problem had been caused by spark plug carbon deposition or ignition coil damage, but these symptoms did not disappear after the replacement of spark plug and ignition coil, indicating that the automobile may have misfire. Today we're going to talk about an engine misfire.

James Smith        July 16, 2020

The breaker-point ignition system also called conventional ignition system. The following points should be noted in the use and maintenance of the breaker-point ignition system. 1. The low-voltage terminals of the ignition coil must be correct and reliable, otherwise, the primary current will be too low to start the engine, Or the ignition coil overheats and burn in the operation of engine because of the primary current is too large. 2. When stopping the car, the ignition switch should be disconnected in time, in order to avoid primary ignition coil being overheated and burned by a large steady current for a long time. The contact of the breaker should be closed when the engine is shut off. 3. The fault probability of breaker contact point is very high, including erosion, dirt and improper gap, which can affect the operation for the ignition system. Therefore, you should check the breaker contact point and contact point gap regularly. If necessary, contact point should be

James Smith        July 16, 2020

The ignition coil is responsible for distributing the ignition sequence and transmitting the pre-allocated high-voltage electricity from the distributor to the spark plugs to ignite the cylinders. The number of ignition wires is determined by the number of cylinders in the engine and each ignition wire is connected to a spark plug with an ignition coil on one side and a distributor.

James Smith        July 15, 2020

Each block/pack includes 2, 4 or 6 ignition coils combined into a single unit. HT leads are used to connect the outlets of the block coil to the spark plugs. Block coils feed voltage to either one or two cylinders simultaneously. Used in modern systems with no distributor.